IU-Series
Door Intercom
Includes models:
IU-0xxx, IU-5xxx, IU-6xxx
IU-0xxxP, IU-5xxxP, IU-6xxxP
Channel Vision’s IU-Series are 1/4" solid brass door plates that interface with other products to provide communication with the front door. It is available in a variety of configurations including options for a hidden camera and compatibility with Panasonic’s popular KSU phone systems. A standard single gang junction box is supplied with each IU-series unit.
Panasonic compatible with camera
Channel Vision’s IU-5xxxP & IU-6xxxP Series are 1/4" solid brass door plates with integrated mini cameras. They are The IU-5xxxP contains a Black & White camera, while the IU-6xxxP contains a color camera. ese s a compatible replacement for the Panasonic KXT30865. The product interface with Panasonic’s KSU phone systems to provide communication with the front door.
Installation:
• Mount single gang junction box.
• Using a 2-conductor wire, connect you Panasonic KSU to the empty screw terminal block on the IU (see diagram).
• If necessary, attach the camera’s video output to a coax extension that is long enough to reach your monitor or video distribution equipment.
• If necessary, cut the connector off of the end of the power supply and splice in an extension using crimp-on connectors.
 Channel Vision compatible (model IU-0xxx)
Channel Vision’s IU-Series are 1/4" solid brass door plates that interface with the Channel Vision TE110 or C-0920 to provide communication with the front door. A standard single gang junction box is supplied with each IU-series unit.
Installation:
• Mount single gang junction box.
• Using a 2-conductor wire, connect the TE110 (C-0920) to the empty screw terminal block on the IU (see diagram).
• Adjust speaker volume to the desired level.
 Channel Vision compatible with camera
Channel Vision’s IU-5xxx & IU-6xxx Series are 1/4" solid brass door plates with integrated mini cameras. They interface with the Channel Vision TE110 or C-0920 to provide audio and video communication with the front door. The IU-5xxx contains a Black & White camera, while the IU-6xxx contains a color camera.
Installation:
• Mount single gang junction box.
• Using a 2-conductor wire, connect the TE110 (C-0920) to the empty screw terminal block on the IU (see diagram).
• If necessary, attach the camera’s video output to a coax extension that is long enough to reach your monitor or video distribution equipment.
• If necessary, cut the connector off of the end of the power supply and splice in an extension using crimp-on connectors.
 Panasonic compatible (model IU-0xxxP)
Channel Vision's IU Panasonic Series models are a compatible replacement for the Panasonic KXT30865. These 1/4" solid brass door plates provide an attractive alternative to the standard plastic door station sold by Panasonic. This product interfaces with Panasonic’s KSU phone systems to provide communication with the front door.
Installation:
• Mount single gang junction box.
• Using a 2-conductor wire, connect the door phone output of your Panasonic KSU to the empty screw terminal block on the IU (see diagram).
• Consult your Panasonic manual for instructions regarding door phone operation.
IU-Series
Telephone Entry Door Intercom
Includes models:
DP-XXXX
DP-XXXXC
DP-XXXXP
Channel Vision’s DP-Series are 1/4” solid brass door plates that interface with a telephone entry controller to provide communication with the front door. They are available in a variety of configurations including options for a hidden camera and compatibility with Panasonic’s popular KSU phone systems. Each plate comes with the DP-9001 or DP-9002 surface mount box (depending on the finish color). It is compatible with the DP-Rbox-II flush mount box, which is sold separately.
Attaching the Companion Board
(DP-XXXX and DP-XXXXP)
The door intercom product consists of two sub assemblies, which must be attached to each other before the final assembly can be installed. In this guide, the electronic sub assembly will be referred to as the “Companion Board” and the mechanical assembly will be referred to as the “Door Plate.”
Remove the plastic cap that covers the microphone compartment on the door plate. Place the microphone in the compartment and replace the plastic cap over the microphone. Note that the plastic cap will form a friction fit over the top of the microphone wires holding them snug against the outer compartment wall until they exit at the base as shown. Remove the mounting screws which are already attached to the bracket and use them to attach the companion board. The companion board should mount on the front side of the bracket so that the screws pass through the companion board before threading into the bracket.
Attaching the Camera
(DP-XXXX and DP-XXXXP)
The DP-5xxx, DP-5xxxP, DP-6xxx, and DP-6xxxP come with a mini camera that can be attached to the integrated mount that allows the camera to see through the opening in the plate.
Break away the section of the perforated metal screen that covers the camera opening by pushing a screwdriver through the slot of the front of the door plate. Press near the top or bottom of the section and the tabs that hold it in place will break free. Attach the camera to the mount so that the cone of the camera points through the opening. Adjust the camera to the desired position and secure it in place by tightening the screw in the mount.
Attaching the Companion Board
(DP-XXXXC)
This door intercom product consists of two sub assemblies which must be attached to each other before the final assembly can be installed. In this guide the electronic sub assembly will be referred to as the “Companion Board” and the mechanical assembly will be referred to as the “Door Plate.”
Position the companion board onto the three mounting tabs. The microphone attached to the back side of the companion board should line up with the microphone tube on the bracket. Bend the mounting tabs to secure the companion board. Connect the speaker and button wires by sliding the small connector over the exposed pins on the companion board.
Attaching the Camera
(DP-XXXXC)
The DP-5xxxC and DP-6xxxc come with a mini camera that can be attached to the integrated mount that allows the camera to see through the opening in the plate.
Break away the section of the perforated metal screen that covers the camera opening by pushing a screwdriver through the slot of the front of the door plate. Press near the top or bottom of the section and the tabs that hold it in place will break free. Attach the camera to the mount so that the cone of the camera points through the opening. Adjust the camera to the desired position and secure it in place by tightening the screw in the mount.
Channel Vision Compatible (DP-XXXX)
Channel Vision’s DP-0xxx does not come with a camera, but the DP-5xxx & DP-6xxx Series door plates come with mini cameras which attach to the integrated camera mount. The DP-5xxx contains a Black & White camera, while the DP-6xxx contains a color camera. The DP-0xxx, DP-5xxx, and DP-6xxx all interface with the Channel Vision’s telephone entry controllers: TE110, C-09020 and P-0921 to provide audio and video communication with the front door.
Installation:
• Install a compatible mounting box at the desired location, such as: DP-Rbox-II flush mount box, DP-9001 surface mount box, or DP-9002 surface mount box.
• Using a 2-conductor wire, connect the Telephone Entry Controller to the empty screw terminal block on the DP.
• If necessary, attach the camera’s video output to a coax extension that is long enough to reach your monitor or video distribution equipment.
• If necessary, cut the connector off of the end of the power supply and splice in an extension using crimp-on connectors.
Panasonic Compatible (DP-XXXXP)
Channel Vision’s DP Panasonic Series models are a compatible replacement for the Panasonic KXT30865. These ¼” solid brass door plates provide an attractive alternative to the standard plastic door station sold by Panasonic. This product interfaces with Panasonic’s KSU phone systems to provide communication with the front door. Model DP-6xxxP includes a color camera, model DP-5xxxP includes a Black & White camera, and DP-0xxxP includes no camera.
Installation:
• Install a compatible mounting box at the desired location, such as: DP-Rbox-II flush mount box, DP-9001 surface mount box, or DP-9002 surface mount box.
• Using a 2-conductor wire, connect the Telephone Entry Controller to the empty screw terminal block on the DP.
• If necessary, attach the camera’s video output to a coax extension that is long enough to reach your monitor or video distribution equipment.
• If necessary, cut the connector off of the end of the power supply and splice in an extension using crimp-on connectors.
Channel Vision CAT5 Intercom Compatible
(DP-xxxxC)
The diagram below shows how to connect the DP-xxxxC to Channel Vision’s CAT5 Whole-House Intercom system. When the button is pressed on the DP-xxxxC the ST-2000 Intercom Stations will generate a door chime. Pressing Answer/End will open communication with the DP-xxxxC. Model DP-6xxxC includes a color camera, model DP-5xxxC includes a Black & White camera, and DP-0xxxC includes no camera.
Installation:
• Install a compatible mounting box at the desired location, such as: DP-Rbox-II flush mount box, DP-9001 surface mount box, or DP-9002 surface mount box.
• Using a CAT5 wire, connect the P-0930 to the 110 connector on the DP.
• If necessary, attach the camera’s video output to a coax extension that is long enough to reach your monitor or video distribution equipment.
• If necessary, cut the connector off of the end of the power supply and splice in an extension using crimp-on connectors.
|
Solutions 
